Vibration Meter

Lay your phone on a surface to measure how much it shakes, and how fast.

0.00m/s²
Still
Tap Start, then lay your phone flat on the surface
side to sidetop to bottomup and down
–Peak
–Average in g
–Main frequency
–As rpm
  1. Tap Start and allow motion access if your phone asks.
  2. Lay the phone flat on the surface and take your hand away.
  3. Read the big number for strength and Main frequency for speed.

How to Use the Vibration Meter

Tap Start and lay your phone flat on the thing you want to measure: a washing machine lid, a desk, a car dashboard, a floor. Take your hand away. The big number settles on the strength of the vibration, and the trace underneath draws it as it happens, like a seismograph.

Lying flat matters. A phone held in the hand mostly measures the hand, and a phone in a soft case or on a cloth is cushioned from the surface. For the cleanest reading, take the case off and rest the phone directly on something hard.

Pause freezes the screen so you can read it or take a screenshot. Reset peak clears the strongest jolt recorded so far. Save CSV downloads the last minute of readings as a file you can open in a spreadsheet, which is useful if you need to show someone when a vibration happened.

What the levels mean

LabelAverage, m/s²Feels like
Stillbelow 0.05A quiet room. Sensor noise only.
Faint0.05 to 0.2A fridge running, someone walking nearby.
Noticeable0.2 to 0.8A desk with a printer working, a car idling.
Strong0.8 to 3A washing machine on spin, a bus on a rough road.
Severeabove 3Power tools, a phone being shaken in the hand.

These bands are a rough guide for comparing one reading with another. They are not a health or safety standard.

What it cannot do

A phone samples motion about 60 to 100 times a second, so it only sees vibration slower than roughly 30 to 50 times a second. The whine of a drill bit or the hum of a transformer is too fast for it; that is sound, and the noise meter or the spectrum analyzer will show it instead.

Frequently Asked Questions

Can a phone really measure vibration?

Yes, within limits. Every smartphone has an accelerometer, the same chip that rotates the screen and counts steps. It senses movement in three directions about 60 to 100 times a second, which is enough to see a washing machine on spin, footsteps on a floor, a running engine or a passing truck. It is not a calibrated instrument, so use it to compare, to spot a change, and to find where a vibration is strongest, not to certify a reading.

What do the numbers mean?

The big number is the strength of the shaking averaged over the last second, in metres per second squared (m/s²). The same value is shown in milli-g, where 1,000 mg is the pull of gravity. Peak is the single strongest jolt since you last reset it. Main frequency is how many times a second the vibration repeats, in hertz, and multiplying by 60 gives revolutions per minute for anything that spins.

Why is the reading not zero when the phone is still?

The sensor has a small amount of electrical noise, usually between 0.01 and 0.05 m/s². A building also never sits perfectly still: lifts, traffic and your own hand on the table all register. Anything the page labels Still is at or below that floor.

Is this a seismometer? Can it detect earthquakes?

It works on the same principle, and a phone lying on a solid floor will show a nearby earthquake that people can feel. It cannot detect distant or very small quakes; real seismometers are thousands of times more sensitive and are bolted to bedrock. Treat the trace here as a seismograph for your own table or floor.

How do I find where a vibration is coming from?

Reset the peak, lay the phone flat at one spot for ten seconds and note the average. Move it and repeat. The reading is highest closest to the source or at the part of the structure that is resonating. The main frequency helps too: a steady 25 Hz points to a motor turning at 1,500 rpm, while a slow 2 Hz bounce is more likely people walking.

Why does my iPhone ask for permission?

Safari does not let a web page read motion sensors until you allow it. Tap Start and then Allow. The readings are worked out on your phone and are not uploaded; the CSV file is created on your device too.

More tools

Water EjectPush water out of your phone speakerVocal Range TestFind your lowest and highest noteSpeaker TestCheck left, right, bass and treble